You are here:
- Knowledgebase
- Product Information
- EZABL
- Unified Firmware Wanhao Duplicator i3 Plus Information
< Back
Adding the Unified Firmware to the Wanhao i3 Plus is a little more involved due to the use of its DWIN touch screen display. Fear not! We will go over the steps to install the firmware on the LCD and the board itself in the video below.
Once your printer is updated you can use our EZABL kit to take all the hassle out of leveling your bed! Pick up a kit here: EZABL™ Pro – Plug & Print Auto Bed Leveling Kit
- Adjusting the EZABL Mini Sensor Adjustment
- Advanced EZABL and Printer Troubleshooting
- Converting the EZ Connect to Direct Wire
- Direct Wire 12V/24V Power Info
- EZABL - Firmware Setup for "Vanilla" Marlin
- EZABL - Tevo Tarantula Pro Z Endstop Cable
- EZABL & EZABL Pro Installation Guide
- EZABL & EZBoard - Not Triggering Fix
- Geeetech A10 3 Pin Z Wiring Notes
- Geeetech A10, A10M, A20, A20M Z Endstop Wiring for EZABL
- Heater Recovery After G29
- How to fix “Slanting” Bed Leveling Result
- Is your EZABL working well? (M48 Test)
- Sensors and Gantry Grounding
- Storing Bed Leveling Mesh & Updating Your Slicer
- Tips for EZABL accuracy
- Unified Firmware Wanhao Duplicator i3 Plus Information
- Using the EZABL with CR-10S Printers with Touch LCD
- Z Axis Troubleshooting
- Z Not Showing “TRIGGERED” M119 Test
- EZPi Getting Started Documentation
- EZPi/Octoprint - Printer Not Connecting Due to "EEPROM datasize error"
- Heaters Shutting off After Probing – OctoPrint “ABL Expert” Plugin Issue
- Octopi/EZPI : "You should consider upgrading via the ‘pip install –upgrade pip’ command" Not Working
- OctoPrint Not Updating and/or Cannot Install Plugins
- Raspberry Pi Direct Wire Power Adapter - How to connect
- 12864 LCD Screen Not Lighting Up
- Aluminum Extruder V1 Assembly Video
- Creality Mega 2560 Board Connections (CR-10S/Dual Board)
- Creality Melzi Board Connections (CR-10/Ender 3/Ender 5)
- Dual Extrusion Setup Information
- Ender 3 Dual Z Kit Installation Guide
- Ender 3 Dual Z Kit PSU Relocation STL Links
- EZMat/EZPei – Adhesion Tips and Tricks
- Fitting Fans to Creality Machines - Larger Metal Standoffs
- MKS Gen L Board Connections
- PTFE Safety Precautions – ALL PTFE & ToughTube
- TH3D Solid Bed Mounts Installation Information
- Thermistor Reading 290+C
- Tough Extruder or E3D Titan Assembly
- Upgraded Aluminum Extruder Installation Video
- Using your All Metal Hotend
- 12864 LCD Screen Not Lighting Up
- 3D Printer Help Guide Creality & Others
- Arduino IDE for Mac OS X Setup Guide
- Creality CR-10 and CR-10S Models – What Printer do you have?
- Creality Mega 2560 Board Connections (CR-10S/Dual Board)
- Creality Melzi Board Connections (CR-10/Ender 3/Ender 5)
- Dual Extrusion Setup Information
- EZABL - Firmware Setup for "Vanilla" Marlin
- EZPi/Octoprint - Printer Not Connecting Due to "EEPROM datasize error"
- Flashing Firmware with an Uno - Useful if your printer USB port is bad
- Integrating a Keenovo silicone heater into an EZABL system
- MKS Gen L Board Connections
- P.I.D. Auto Tune Guide