40mm Sealed Bearing Fan (24V) – Quiet (25dBA)

Compatible Machines:

• Ender 3/3 V2/5/5Plus
  • Hotend and Control Box
  • Install Notes – Depending on your revision you may need to widen the holes a little on the fan screw holes themselves (use a file or drill bit slightly larger than the stock holes) to get them to slip over the metal posts, or use slightly longer screws.
• CR-10S Pro
  • Hotend Fan and Control box Rear
• Tevo Tornado
  • Hotend
• Geeetech A10 V1
  • Hotend and Control Box
• Sunlu S8
  • Hotend and Control Box
• Wanhao D6
  • Hotend, Layer Fan, and Control Box
• Wanhao i3 Mini
  • Hotend and Control Box

Installation Notes:

• Be sure to check the polarity on the wires you are connecting our fans to. Typically red is positive and black is negative but some of the Chinese printers to not adhere to these standards.
  • There is no list of what machines use what as it can vary from model to model and we have even seen differences in wiring colors used in the same printer models.
• Our fans use red for positive and black for negative. You can verify polarity with a cheap $10 multimeter from Amazon or you local hardware store.
  • If fans are shorted out/killed due to improper wiring this is NOT covered under warranty.
• Some Creality machines have been reported to have larger size metal screw standoffs. If your fan holes do not fit over them please see this article to make the fan fit correctly while still using the stock screws.
  • Fan Mod Article: Fitting Fans to Creality Machines – Larger Metal Standoffs
• Noise notes:
  • In our testing and per the manufacturer specs these are quieter than stock fans based on dB measurements taken with a calibrated dB meter.
  • Removing and/or changing the design of the grill that the fan is behind will change the noise level that is perceived to your ears and it is subjective based on the person listening.
  • We only use dB meters to check noise levels. Most stock fans are 30-35dB in noise levels based on measurements of the stock fans from Creality, Tevo, and Wanhao that we measured here.
  • It is said that every 10dB increase in noise is perceived as 2x the loudness that a person hears (see here for detailed info on loudness and how it is perceived).

Tech Specs

• Airflow: 6.7 CFM
• Voltage: 24V DC
• Noise: 25dBA
• RPM: 6000
• Power: 1.4W
• Wire leads: 2 wire
• Life Rating: 50,000 hours (5+ years)
• Other features:
  • Reverse Polarity Protection
  • Auto Restart
• 2 “UY” quick connectors for solder-free installation
  • See picture below for how to use. Use WIDE pliers and apply equal force.
  • Make sure wires are straight and centered in the connector before squeezing.

Quick Connectors Information

Please read our documentation on using the included UY connectors here: How to use our Fan Quick Connectors (UY Style)

• Support/Warranty
  • Included Support: TH3D Community Support
  • Warranty: 90 Days

Warranty & Support Information

Technical Support: TH3D Community Support

Technical support with for product it is handled through our TH3D Communities. You can get access to them on our Community Page. If you require consulting time direct from the TH3D team to use/install the part it is available for an additional, hourly consulting charge.

Warranty Length: 3 Months

Our warranty covers any and all defects with the product. If your product fails or has problems within the warranty period you can contact our support team by using the Contact Us link. This is for warranty related issues only, not technical support. Damage/Failure due to improper installation, usage, failure resulting from an issue with the machine the product is installed on, and/or modification or the product is not covered under warranty