V6 Heavy Duty Mount For Ender 3 & CR-10 – 5015 Fan and EZABL (ABS)
From: $14.99
- 100% Made in the USA with ABS Plastic
- 5015 Fan Needed for Layer Fan
- Uses 40mm Stock CR-10 Fan
- Mount for EZABL Sensor
- Works with all E3D and 3rd Party V6 hotends
- Check out our Tough Hotend (V6 Compatible) Here: Tough All-Metal Hotend
This is the printed parts ONLY. 5015 Fan Required for layer fan.
This works with the following models:
- CR-10
- CR-10 Mini
- CR-10 S4
- CR-10 S5
- CR-10S
- CR-10S Mini
- CR-10S S4
- CR-10S S5
- Ender 3/3 Pro
Products Pictured:
All screws and nuts needed for this are M3 size. We carry screw assortments if you do not have extra screws. The longest screws used here are M3 x 25mm (2 for the hotend clamp). Do not use screws with a tapered head as this can break the part.
Pictures are of the actual print quality. Supports are removed before shipping. Printed at 0.2mm Layer height 35% infill.
Uses a 5015 layer fan and has a spot for our EZABL sensor. Works with our V6 hotend.
Probe offsets for firmware – This is pre-setup in our firmware already.
#define X_PROBE_OFFSET_FROM_EXTRUDER 63 // X offset: -left +right [of the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
STL Files via Thingiverse: https://www.thingiverse.com/thing:2494642
STL files via Printables: https://www.printables.com/model/214737-cr-10-heavy-duty-customisable-modular-e3d-v6-mount
Warranty Information
3 Months Warranty - Our warranty covers any and all defects with the product. If your product fails or has problems within the warranty period you can contact our support team by using the Contact Us link.
Damage/Failure due to improper installation, improper usage, failure resulting from an issue with the machine the product is installed on, 3rd party products connected to our product, and/or modification of the product are not covered under warranty.
This design is based on the “Chito” design (we mirrored the ABL+5015 wing). We have spoken to him and he has given us the OK to sell these in the store. Check out his original mount and files here:
Thingiverse – https://www.thingiverse.com/thing:2494642
Printables – https://www.printables.com/model/214737-cr-10-heavy-duty-customisable-modular-e3d-v6-mount
ABS Parts are BLACK.
Share your thoughts!
Let us know what you think...
What others are saying
Related products
Click Add to Wishlist to be emailed when we re-stock this item.
Click Add to Wishlist to be emailed when we re-stock this item.
Click Add to Wishlist to be emailed when we re-stock this item.
Click Add to Wishlist to be emailed when we re-stock this item.
Click Add to Wishlist to be emailed when we re-stock this item.
agz (verified owner) –
The product itself is fine. It is entirely compatible with the Ender 3 V2 carriage and mounted right up. The material seems durable. Unless you can print ABS yourself this is a great option but there are some buyer bewares you should be aware of.
The durability comes at a cost. At least for me there was significant fit and finish work needed to make everything work correctly. Aside from the expected countersinking needed to get the front fan mounted I also needed to sand the every recess for the hex nuts. This was relatively painful as the holes are small and ABS is pretty robust to sanding. It took a little bit to get things in place. You may or may not have the same problem with your print, however I’m sure due to thermal expansion and which printer it’s printed on you may encounter this issue.
As a suggestion to people buying this:
1. The back hex nut recesses can be reamed using the hex nut itself. If you are careful you can start your screw from the front, twist a hex nut from the back and line it up with the hole. Carefully begin tightening unless you feel the nut completely stop. You will be embedding the nut in the plastic using this method and its far easier than getting sand paper into the hole.
2. For the top EZABL mounts – the bottom shelf may need to be cut. You can try to take an exacto knife in there if you are careful and widen the hole. I had to do this because otherwise the nut would not sit flush with the entry hole on the other side causing cross threading of the bolt.
Overall it’s not terrible. I cant be too upset because really this is a kind service by Th3D. But buyer beware – you will need to do some (sometimes significant) fit and finish work.
(2) (0) Watch Unwatch
recreant359 (verified owner) –
Came pretty decent quality, needed a little bit of trimming. Not a lot of guides online to help with assembly, but with enough time you can figure it out.
(0) (0) Watch Unwatch
fursphere –
Will this work on an Ender 3 and/or Tevo Tornado?
(0) (0)
Tim Hoogland –
Yes, they all use the same X carriage.
(0) (0)
bktransactions –
As mentioned by recreant359, it needs a little TLC (trimming) to fit. Also go to Amazon and get a kit of M3 screws, locknuts, washers and lockwashers (you’ll need them for other projects) which include the ones recommended in the Thingiverse description – although I think some were too long and I switched to shorter ones (that’s why you should have a kit of screws). I installed TH3D’s tough V6 hotend and 5015 fan along with EZABL. Everything assembled nicely and works great – just got my first print off the build plate. I gave it 4 stars because I am a tough (but honest) critic because of the extra time needed to trim the mount to fit the v6 hot end heatsink. Overall I am happy and you will be too.
(0) (0) Watch Unwatch
deleonc (verified owner) –
purchased 2 of this for the cr-10, plenty of power. wont be seeing 100% on both. did need to trim just a bit to slid into the mount from thingiverse no big deal. easy to install i chose to solder them in, but do come included with crimp connectors.
(0) (0) Watch Unwatch
Question
Howard Edidin (verified owner) –
Does know how to mount the
CR-10/CR-10S V6 Heavy Duty Mount – on an Ender 3? I
I have the main mount but can not figure out how to mount the fan /ezable mount
(0) (0) Watch Unwatch
Tim Hoogland –
The Ender 3 uses the same carriage as the CR-10. You can see this mount on our CR-10 Mini in the video here: https://www.youtube.com/watch?v=6oRz0HudAW4
(0) (0)
Question
Gabe –
Would this work on an Ender 3 v2?
(0) (0) Watch Unwatch
Tim Hoogland –
The Ender 3 V2 has a different carriage than the normal Ender 3 so it will not work.
(0) (0)
Question
Marcus Bustos –
can it work with sovol 01?
(0) (0) Watch Unwatch
Tim Hoogland –
This will not fit the SV01 since it uses a different carriage design.
(1) (0)
Question
Emerson Corder –
Is there a way to make this work with the tough extruder?
(0) (0) Watch Unwatch
Tim Hoogland –
This is only compatible with the Tough Extruder when you use it in a bowden configuration, not direct drive.
(0) (0)