EZABL Kit – Direct Wire (12V) Version – PREORDER

Rated 5.00 out of 5 based on 1 customer rating
(1 customer review)

$60.00

We are going to be unavailable for the wedding/bachelor party from 10/17-10/23 and 10/27-10/29. Then again for the honeymoon from 11/8-11/15.

We are ordering a LARGE quantity of components for the kits and we just got over 100 in yesterday. These would NOT ship until at least the last week of October/First week of November. Also if we get a TON of orders we will be processing the pre-orders in the order they were received. TLDR if we get 100 orders it will take longer for the last orders to be processed and shipped. DO NOT ORDER IF YOU DO NOT WANT TO WAIT. THIS PRE-ORDER IS BY POPULAR DEMAND SO EVERYONE CAN GET THESE.

Easily Add Auto Bed Leveling to your 3D Printer!

  • Includes Bed Sensor, EZABL Module, 3ft of Wire to run to 12V, and Printed Enclosure for EZABL Module (Black)
  • Works on Glass, Aluminum, Buildtak, Acrylic, and more (AC BEDS MAY NOT WORK WITH THIS KIT, SEE NOTES BELOW)
  • Full Installation Documentation Included
  • FREE Support Included with Kit
  • 100% Original Kit Developed and Assembled in the USA

Available on backorder

9 people are on the notification list.

Description

We are going to be unavailable for the wedding/bachelor party from 10/17-10/23 and 10/27-10/29. Then again for the honeymoon from 11/8-11/15.

We are ordering a LARGE quantity of components for the kits and we just got over 100 in yesterday. These would NOT ship until at least the last week of October/First week of November. Also if we get a TON of orders we will be processing the pre-orders in the order they were received. TLDR if we get 100 orders it will take longer for the last orders to be processed and shipped. DO NOT ORDER IF YOU DO NOT WANT TO WAIT. THIS PRE-ORDER IS BY POPULAR DEMAND SO EVERYONE CAN GET THESE.

The EZABL Kit is a fully original design that makes adding an Auto Bed Leveling Sensor to your printer much easier than DIY solutions.

***This version requires hooking up the included power wire to your 12V printer power supply. If you are not comfortable running wire or it’s difficult to get access to your printer power supply then look a the EZ-Connect version which has it’s own power adapter.***

You will receive a full kit that includes:

  • All the wiring for power (1 Meter)
  • Sensor with 1 Meter Cable
  • Our Original EZABL module
  • Printed Case for the EZABL module – Color is Black
  • Full documentation on getting it up and running (Provided in a PDF Format)
  • Works with ANY printer that runs Marlin and our support can help you get it running and setup. If you are unsure about what your printer runs please Contact Us.
    • For CR-10 users we have pre-compiled and setup firmware for you available for free with purchase.

There is also FREE email support included to help you get going and printing with a leveled bed

Extensive firmware setup assistance – phone, messenger, or video chat – is available but there may be a charge for this due to the involvement required or what the issue is. Meaning if you want to add ABL and aren’t familiar with your board/printer firmware I can assist you with this.

This kit has been in development for 6 months and has been proven to be accurate and reliable. It works on Glass, Aluminum, Steel, BuildTak, and many other solid surfaces.

***IF YOU HAVE AN AC POWERED BED THE AC CURRENT MAY INTERFERE WITH THE SENSOR ACCURACY. IF YOU HAVE AN AC BED WE DO NOT RECOMMEND TURNING IT ON OR DOING THE CALIBRATION WITH IT ON. WE WILL NOT BE REPLACING SENSORS DUE TO AC INTERFERENCE AS THEY ALL ARE AFFECTED BY THIS (NOT JUST OUR SENSORS BUT ALL CONTACTLESS SENSORS). YOU WILL HAVE TO TURN IT ON MANUALLY OR IF YOU HAVE A SSR HAVE YOUR SLICER KICK IT ON AFTER THE G29 COMMAND***

If you have any inquiries feel free to Contact Us!

90 Day Warranty Against Defects – Physical or Electrical Damage due to improper installation or use is not covered. Items are all pre-tested before leaving the shop.

By purchasing this item and any item in this shop you agree to the Terms of Service.

Additional information

Weight 6 oz
Dimensions 6 x 4 x 2 in

1 review for EZABL Kit – Direct Wire (12V) Version – PREORDER

  1. Rated 5 out of 5

    dubbedout (verified owner)

    I’m new to the 3D printing world and was struggling to keep my CR-10 bed level and get good consistent results. This kit was very easy to install, the instructions are very detailed and any issue I ran into was fully documented in the instructions.

Add a review

You may also like…

We have the EZABL and other products as a PREORDER since we are going to be tied up with wedding things. Please read the product pages for expected shipping times. Dismiss