Cart

Subscribe to TH3D News via Email

Enter your email address to subscribe to this blog and receive notifications of new posts by email.

Join 2,544 other subscribers

EZABL Kit – EZConnect V3.1 – CR-10, CR-10S, Ender 2, Ender 3, Tornado, Alfawise U10

Rated 5.00 out of 5 based on 5 customer ratings
(5 customer reviews)

$64.99

Easily Add Auto Bed Leveling to your 3D Printer! NO soldering at all!

  • Includes the TH3D V3.1 EZABL Sensor pre-wired to our EZABL V3 Board and Power Adapter (AC or USB)
  • Works on Glass, Mirror, Aluminum, Buildtak, Acrylic, and more
  • Full Installation Documentation Included in the EZABL Customer Package
  • Pre-setup Firmware Included FREE to get you going quick with mounts
    • Sensor mount NOT included as we support many models. We include a STL pack with all the mounts.
    • If you need a mount printed you can contact us and we can let you know. Some we will do for free (like the smaller OEM Mounts) others do have a charge.
  • Support over Email is included with the kit through our TH3D Help Desk
  • 100% Original Kit Developed, Designed, and Assembled in the USA by TH3D (We build every kit by hand)
Clear

Description

The EZABL Kit is a fully original design that makes adding an Auto Bed Leveling Sensor to your printer much easier than DIY solutions with full support included should you need it.

***This version has it’s own power adapter. If you want to use the existing 12V or 24V from your printer PSU then check out the Direct Version here***

Installation Video:

Shipping Time Note: All EZABL Orders ship in 1-3 days as we hand make them here in the US.

You will receive a full kit that includes:

  • TH3D EZABL V3.1 Sensor pre-wired to our EZABL V3 Board and Power Adapter (AC or USB)
    • USB Power Adapter puts out 12V so sensor is as accurate with them as they are with the AC adapter.
    • Now includes the EZ-Direct Adapter tip should you want to wire power from the printer later on instead of the included power adapter.
  • Works on Glass, Mirror, Aluminum, Buildtak, Acrylic, and more
    • If you have an AC bed please see notes below about using it with the EZABL
  • Full Installation Documentation Included in the EZABL Customer Package
  • Pre-setup Firmware Included FREE to get you going quick
    • Sensor mount NOT included as we support many models. We include a STL pack with all the mounts.
    • If you need a mount printed you can contact us and we can let you know. Some we will do for free (like the smaller OEM Mounts) others do have a charge.
  • Support over Email is included with the kit through our TH3D Help Desk
  • 100% Original Kit Developed, Designed, and Assembled in the USA by TH3D (We build every kit by hand)
  • Tech Specs:
    • High Quality AC Adapter for smooth voltage output
      • USB Adapter needs a clean power source – Do not use with low end USB phone adapters
    • Onboard Power Filtering & Decoupling
    • High Speed Toshiba Optocoupler IC
    • Reverse Voltage Protection
    • High quality copper, 2 Layer PCB w/ Full Ground Plane
    • TH3D V3.1 100hz 18mm Capacitive Sensor – ONLY available from TH3D
      • Weighs only 40 grams
      • Fully shielded sensor cable to reduce EMI interference – V3.1 sensors are on kits ordered AFTER 9/12/2018
  • Works with ANY printer that runs Marlin but this kit is geared for the below machines that have a 2/3 pin JST Z endstop.
  • Some printers require a bootloader that needs an Uno to be flashed. Please check the Unified Firmware page to see if yours needs one (CR-10, Wanhao i3, Ender 2, Ender 3)

Support/Warranty

  • Included Support: TH3D Standard Support
    • Support is on the product itself. Your computer must see the printer COM port to update the firmware. PC issues are the customers responsibility to resolve.
  • Warranty: 90 Days
    • Physical or Electrical Damage due to improper installation or use is not covered. Items are all pre-tested before leaving the shop.

Extensive firmware setup assistance – phone, messenger, or video chat – is available but there may be a charge for this due to the involvement required or what the issue is. This does not apply if you are using a pre-supported printer listed above. Meaning if you want to add EZABL and aren’t familiar with your board/printer firmware we can assist you with this.

AC Bed Notes:

If you have an AC bed the frequency of the AC current can throw off the accuracy of the sensor. This can be avoided by simply turning off the AC bed when Z homes and G29 runs. Once those are completed you can turn the bed back on. If you use a SSR to control the AC bed (like what the Tevo Tornado has from the factory) the firmware will automatically manage this for you. If you are doing your own DIY SSR+AC Bed setup we highly recommend the MSSSR20 SSR from Misumi as it has very low AC leakage current. Some low quality SSRs will leak a small amount of AC current and can affect the sensor even when in the off state. There is a guide on our knowledgebase about using a wifi outlet + raspberry pi to manage a standalone heater.

Tevo Tornado Notes:

Some Tevo Tornado printers shipped with very low quality power supplies that have an open or poor ground and/or Solid State Relays that leak AC current. This can cause the kit to not work. Unless you have a high end multimeter or scope to check the grounding and ripping on the machine there is no way to tell if yours is affected. A new PSU and SSR is between $30-50 and we sell both of these for just a hair over cost to make replacements easy. If you end up not wanting to swap the PSU and SSR and you have a Tornado we will waive the restocking fee if you choose to return it. This affects our sensors, other similar types, and even BL Touch sensors (clones included).


If you have any inquiries feel free to Contact Us!

5 reviews for EZABL Kit – EZConnect V3.1 – CR-10, CR-10S, Ender 2, Ender 3, Tornado, Alfawise U10

  1. Rated 5 out of 5

    mmichaels1010 (verified owner)

    Makes getting a good first layer a breeze.

  2. Rated 5 out of 5

    guitarjc55 (verified owner)

    Takes the hassle out of leveling the heatbed. The directions are very easy to follow, and with pre-built probe mount profiles, it makes setting up a breeze.

  3. Rated 5 out of 5

    tim.btsi (verified owner)

    If you want to add auto bed leveling to your printer but don’t know all the ins and outs of it or the firmware, then this is your answer. When you purchase this kit you get everything you need, the abl, the instructions, the firmware, the mounts for your printer, and the SUPPORT that other companies say they offer but never actually help.
    This kit works, plain and simple. I bought the ez connect version for one printer, then bought the direct wire version for a 2nd printer. Both are easy to install and setup.

  4. Rated 5 out of 5

    Cobey (verified owner)

    Works great! There was some left to be desired with the instructions, and a stock mount would have been nice to have included, but I’m really happy with my purchase

    • Timothy Hoogland

      Thanks for the feedback! We’re putting out our own in-depth installation video in the next few days!

  5. Rated 5 out of 5

    ghost000 (verified owner)

    This product does exactly what is in the description, super easy to install and flash the firmware. My CR-10S is printing better than ever now.

Add a review

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.