Specifications
- 1mm thick magnet for high strength
- Genuine 3M 300LSE Adhesive Pre-Applied
- Rated up to 140C Bed Temperature
- This is for the MAGNET ONLY. You still need a plate and we carry them here: EZFlex Pro – Dual Sided Black Textured PEI Flex Plate
Bed Size Not Listed?
- Magnets can be trimmed or cut easily with a knife or scissors so order a size larger than your bed if you do not see your exact size, then cut to fit
Readme
- Do NOT print directly on the magnet. You must have a flex plate on top of it to use this on your printer.
- Do NOT peel the adhesive off with the backing. Make sure you are ONLY peeling the backing paper with the 3M marking on it and not the adhesive as well.
- If you accidentally peel the adhesive off put it back on the magnet and press firmly across the entire magnet. Then use the tip of a knife or something tiny to pull just the backing paper off.
- Before installing make sure your printer bed is CLEAN and free of any debris
- Install directly on your printer bed (aluminum or glass if it is permanently attached)
- Be sure to select the correct size. TH3D is not responsible if you order the wrong size for your printer bed
- Do NOT leave liquids on the magnet or place a plate on the magnet if it is not dry and clean
- Corner style of magnet sheet may vary from picture
Joseph E. (verified owner) –
Always just works, I have this bed magnet on all 3 of my printers. They never fail.
rich s. (verified owner) –
Works great, printed on glass which I glued to a spring steel plate at 120c bed heatwith no issue whatsoever
James G. (verified owner) –
Price was right and it should handle the temperatures I run, so GREAT!
Cody (verified owner) –
Went down smooth, very sticky to help adhesion, very strong magnet holding down the surface. I have no problems thinking this’ll last. Only thing I noticed was that I no longer have access to the screws the bed is attached on my Ender 5 Plus. But I don’t see myself changing out the actual bed anytime soon so I’m not worried about it.
RANDY S. (verified owner) –
Michael R. (verified owner) –
The EZFlex2 magnetic base for the Ender 3 is a game-changer! It made bed leveling a breeze and significantly improved the adhesion of my prints. The magnet is strong, and the build quality is excellent. Installation was quick and straightforward. I can’t recommend this product enough – it’s a must-have upgrade for any Ender 3 owner!
Joseph S. (verified owner) –
prints stick well when warm/hot releases when cold if not just flex a little and parts fall off . use these on all my printers. Put the scraper away no need well worth the cost.
John Mark (verified owner) –
Derek K. (verified owner) –
Russell G. (verified owner) –
Excellent!!
Frank R. (verified owner) –
MARCOS A. (verified owner) –
Almost perfect for a oversized Ender 7 build plate with some extra trimmings around the edge.
Mark J. (verified owner) –
Matt A. (verified owner) –
Easy to apply and strong enough to put some aluminum foil in between the mag sheet and the steel sheet for beds that have a dip in the middle
Jim M. (verified owner) –
Strong adhesion but easily removed for cleaning.
Anthony M. (verified owner) –
Strong magnet, and solid adhesive.
John M. (verified owner) –
Difficult to get aligned.
Tim Hoogland (verified owner) –
One thing we do here is start with one corner and work from there. It makes application easier. Do NOT pull back the adhesive tape all the way either, just a few inches. Then stick it down and work it onto the bed a little at a time.
Donald k. (verified owner) –
Incredible hold at high temperature
Anthony D. (verified owner) –
The magnet was super easy to install and holds the plate firmly even at higher temperatures.
Chaney Goldstein (verified owner) –
Great addition to the EZFlex plate. Very strong and durable.
mcurrier79 (verified owner) –
Tied with a flexplate this makes removing prints faster, easier and most importantly CLEANER.
Mark Thompson –
My 410x410mm magnetic mat is over 1.5 years old at this point and its hold is still sufficient. I frequently use it at 140c and the only damage visible is a bit of corrosion along the edges. Unfortunately, I have outgrown the 140c max temp and I need to remove it, so I figured I’d see how far it would go. Welp it went to 195c for a short period of time and was fine, another run to 200c for an extended period of time and the 3m adhesive failed, no damage to the magnet. This is incredibly impressive and if I need a magnetic mat for another printer I will be buying one from here.
Patrick Havey (verified owner) –
As the title states, I’ve printed over 50 PETG prints at 82 degrees and the magnet shows now sign of fatigue.
John Gianni –
I can’t believe how nice this makes removing prints.. I recommend this product to anyone who has to use scrapers and other things to get prints off the bed. And no issues with adhesion during the print. Thanks TH3D.
fevergeonm (verified owner) –
Utilized this on 3 ender 5’s, works great when combined with the flex PEI built plate!
Joe –
I’ve printed with PETG and Nylon at 80C on the bed and the sheet seems to have the same magnetic strength. The adhesive is extremely sticky, seems like it won’t be peeling off any time soon.
Ken (verified owner) –
Holds the EZFlex plates down great while printing. Also, It was easy to trim the excess off with a razor blade. It is a great replacement for the one that came on my CR-20 Pro.
Brandon Woods (verified owner) –
This is the mounting system I have been looking for. 4 stars because the 220×200 measured 222×222; my 3D printer has a dished out plate, necessitating trimming of the magnetic pad before I could install it. Otherwise a beautiful product.
spudmlgnjr (verified owner) –
Perfect upgrade for my CR-10s Pro. Thanks for offering it so quickly.
spudmlgnjr (verified owner) –
It does what it says for less than the others. How could you go wrong.
chaoswyrm (verified owner) –
Death to clippy! This plus a steel flex plate like the EZFlex plate makes the days of clips getting in the way of nozzles or ABL probing go away.
No negatives to mention. Just peeled and stuck to my Ender3 base plate. EZFlex plate then snaps right down on it. Pulls right up with reasonable lift applied.
Rolo (verified owner) –
I loved mine so much, I bought one for a friend also.
Rolo (verified owner) –
This and the EZFlex plate have made removing prints so much easier. I love it!!