- Works great for long-term use at temperatures up to 140C!
- Genuine 3M Adhesive Backing Pre-Applied to Magnetic Sheet
- Clean your bed with IPA before applying and remove the previous build surface.
- Apply directly to your printer’s heated bed plate.
- Pre-Cut to size for your machine – Pick above
- 1MM Thick Magnet Sheet + 0.2mm 3M Adhesive
- All magnets will be 1-2mm oversized to allow for easy application.
- You can leave it as-is after applying or trim with a sharp knife or deburring tool (as seen in the video).
- NOT meant for printing directly on, only for use with the EZFlex² Flex plate on top of it.
- Looking for the plate and magnetic base? Get the EZFlex² Flexible Print System here!
- These magnetic sheets are meant for use with the plates we sell.
- Do NOT put other surfaces on top of the magnetic base as some have reported that certain mirrors and/or glass can stick to the magnetic sheet which can damage it.
- For best results, apply directly to a bare, clean aluminum bed surface. Attaching the magnetic base to other surfaces, such as polycarbonate or textured surfaces, is not advised nor covered under warranty.
- Bed Sizing Notes
- Be sure to check your bed size. TH3D is not responsible for the wrong size ordered and/or errors in the listings. We try do our best to keep descriptions up to date but some manufacturers make changes to machines after release.
- Cleaning – Keep the top and bottom of the plate clean as well as the magnet if you get anything on it. IPA is what is recommended to clean the plate and magnetic base. Make sure that no liquids or adhesives are on top of the magnet or bottom of the plate. If liquids are between the magnet and the plate it can damage and degrade the magnet so keep them dry and clean.
Installation Video – Covers the entire system installation
Warranty Information
3 Months Warranty - Our warranty covers any and all defects with the product. If your product fails or has problems within the warranty period you can contact our support team by using the Contact Us link.
Damage/Failure due to improper installation, improper usage, failure resulting from an issue with the machine the product is installed on, 3rd party products connected to our product, and/or modification of the product are not covered under warranty.
All plates and magnets are inspected to ensure full functionality to make sure they meet our standards for them. Smooth PEI plates may have a non-uniform appearance under the PEI as that is the adhesive visible through the PEI sheet, this is normal. Textured PEI plates may have a non-uniform appearance as they are sprayed and the PEI is baked onto the plate, this is normal. Only if a plate has a defect that affects it’s functionality will be considered defective.
Return/Refund Information for Flex Plates and Magnets
Once a magnet is installed on a printer it is NON-REFUNDABLE as there is no way to remove it from the bed without damaging it.
Flex plates can only be returned if they are in like-new condition and have no signs of use on their surface.
Rolo (verified owner) –
This and the EZFlex plate have made removing prints so much easier. I love it!!
(1) (0) Watch Unwatch
Rolo (verified owner) –
I loved mine so much, I bought one for a friend also.
(1) (0) Watch Unwatch
chaoswyrm (verified owner) –
Death to clippy! This plus a steel flex plate like the EZFlex plate makes the days of clips getting in the way of nozzles or ABL probing go away.
No negatives to mention. Just peeled and stuck to my Ender3 base plate. EZFlex plate then snaps right down on it. Pulls right up with reasonable lift applied.
(1) (0) Watch Unwatch
spudmlgnjr (verified owner) –
It does what it says for less than the others. How could you go wrong.
(1) (0) Watch Unwatch
spudmlgnjr (verified owner) –
Perfect upgrade for my CR-10s Pro. Thanks for offering it so quickly.
(1) (0) Watch Unwatch
Joe –
I’ve printed with PETG and Nylon at 80C on the bed and the sheet seems to have the same magnetic strength. The adhesive is extremely sticky, seems like it won’t be peeling off any time soon.
(1) (0) Watch Unwatch
Ken (verified owner) –
Holds the EZFlex plates down great while printing. Also, It was easy to trim the excess off with a razor blade. It is a great replacement for the one that came on my CR-20 Pro.
(0) (0) Watch Unwatch
fevergeonm (verified owner) –
Utilized this on 3 ender 5’s, works great when combined with the flex PEI built plate!
(0) (0) Watch Unwatch
John Gianni –
I can’t believe how nice this makes removing prints.. I recommend this product to anyone who has to use scrapers and other things to get prints off the bed. And no issues with adhesion during the print. Thanks TH3D.
(0) (0) Watch Unwatch
Patrick Havey (verified owner) –
As the title states, I’ve printed over 50 PETG prints at 82 degrees and the magnet shows now sign of fatigue.
(0) (0) Watch Unwatch
Mark Thompson –
My 410x410mm magnetic mat is over 1.5 years old at this point and its hold is still sufficient. I frequently use it at 140c and the only damage visible is a bit of corrosion along the edges. Unfortunately, I have outgrown the 140c max temp and I need to remove it, so I figured I’d see how far it would go. Welp it went to 195c for a short period of time and was fine, another run to 200c for an extended period of time and the 3m adhesive failed, no damage to the magnet. This is incredibly impressive and if I need a magnetic mat for another printer I will be buying one from here.
(0) (0) Watch Unwatch
mcurrier79 (verified owner) –
Tied with a flexplate this makes removing prints faster, easier and most importantly CLEANER.
(0) (0) Watch Unwatch