Cart

Subscribe to TH3D News via Email

Enter your email address to subscribe to this blog and receive notifications of new posts by email.

Join 2,552 other subscribers

EZMat Build Sheet – 235×235 Size

Rated 5.00 out of 5 based on 1 customer rating
(1 customer review)

$10.99

  • Proprietary Polycarbonate Blend Build Sheet
  • Genuine 3M High Temp Adhesive Tape Pre-Applied
    • New “EZ-Remove adhesive” that leaves minimal residue on your build plate when replacing the mat.
  • Works with ALL major filament types (PLA, PETG, ABS, PC, ASA, TPE/TPU, and Nylon)
  • 0.6mm Thick for durability and longevity
    • Once you start losing adhesion lightly sand with 100 grit sand paper to make it like new!
  • This is for ONE sheet. Discount for 2 or more.
  • Sheet is 235x235mm
    • Fits Ender 3 Perfectly
    • Fits Geeetech A10 Perfectly
    • Can be trimmed with scissors to fit standard 200×200 or 220×220 beds like the Wanhao i3 and Anet Printers.

Discount per Quantity

Quantity2 -25
Price$9.89

In stock

Description

As seen on “Uncle Jessy” YouTube Channel

  • Proprietary Polycarbonate Blend Build Sheet
  • Genuine 3M High Temp Adhesive Tape Pre-Applied
    • New “EZ-Remove adhesive” that leaves minimal residue on your build plate when replacing the mat.
  • Works with ALL major filament types (PLA, PETG, ABS, PC, ASA, TPE/TPU, and Nylon)
  • 0.6mm Thick for durability and longevity
    • Once you start losing adhesion lightly sand with 100 grit sand paper to make it like new!
  • This is for ONE sheet. Discount for 2 or more.
  • EZMat – Adhesion Tips and Tricks
  • Sheet is 235x235mm
    • Fits Ender 3 Perfectly
    • Fits Geeetech A10 Perfectly
    • Can be trimmed with scissors to fit standard 200×200 or 220×220 beds like the Wanhao i3 and Anet Printers.
  • Recommended Temperature Settings
    • PLA: 0C-60C
    • ABS: 90C
      • Our mats work great with ABS but you MUST use an enclosure for ABS as it warps. If you do not the ABS will stick to the sheet and can pull it off the bed as it warps due to cooling.
    • PETG: 70C
      • PETG has a tendency to like to bond to print surfaces (all brands, not just ours). We recommend using something in-between the mat and the PETG to help it release easier. You can use glue stick or hairspray to prevent this from happening. We use these mats with PETG but we make sure we are not “squishing” it down on the 1st layer as much as you would PLA or other materials. Use a spatula to remove the prints, DO NOT PULL ON THEM OR TRY TO “KNOCK” THEM OFF.
    • TPU/TPE: 70C
  • Returns on mats are only allowed if they have not been used and/or installed.

Support/Warranty

Installation Notes/Tips

  1. Clean the surface with acetone then glass cleaner. If you do not have acetone just glass cleaner will suffice.
  2. Align the bed mat on the bed or glass that you want to apply to
    1. Bond strength can also be improved with firm application pressure and moderate heat, from 38°C to 54°C, causing the adhesive to develop intimate contact with the bonding surface.
  3. Peel back one corner
  4. Slowly apply it to the bed pressing firmly as you peel the backing to avoid getting bubbles under the mat

1 review for EZMat Build Sheet – 235×235 Size

  1. Rated 5 out of 5

    Robert Tate (verified owner)

    I haven’t had any problems with prints sticking to the bed since I put the EZMat on my Ender-3 bed. Big plus, I got rid of the clips holding on the other surfaces I tried (and gave up on).

Add a review

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.