Sale!

EZMat Build Sheet – Multiple Sizes

(35 customer reviews)

$1.99$10.99

  • Proprietary Polycarbonate Blend Build Sheet
  • Available sizes: 165×165, 235×235, 235×310, 310×310, 310×320, 410×410
    • 310×320 can be cut to fit 310×310 machines. It is just 10mm longer on the Y direction.
  • Genuine 3M High Temp Adhesive Tape Pre-Applied
    • New “EZ-Remove adhesive” that leaves minimal residue on your build plate when replacing the mat.\
  • Works with ALL major filament types (PLA, PETG, ABS, PC, ASA, TPE/TPU – Nylon may need glue to hold down completely as well as an enclosure)
  • 0.6mm Thick for durability and longevity – Can be installed directly on the bed or glass.
    • Once you start losing adhesion lightly sand with 100 grit sand paper to make it like new!
Clear

Earn up to 11 Benchies.

Product Info

As seen on “Uncle Jessy” YouTube Channel

  • Proprietary Polycarbonate Blend Build Sheet
  • Genuine 3M High Temp Adhesive Tape Pre-Applied
    • New “EZ-Remove adhesive” that leaves minimal residue on your build plate when replacing the mat.
  • Works with ALL major filament types (PLA, PETG, ABS, PC, ASA, TPE/TPU – Nylon may need glue to hold down completely as well as an enclosure)
  • 0.6mm Thick for durability and longevity – Can be installed directly on the bed, flex plate, or glass.
    • Once you start losing adhesion lightly sand with 100 grit sand paper to make it like new!
  • This is for ONE sheet.
  • EZMat – Adhesion Tips and Tricks
  • Can be cut to fit any size machine – Order size that is slightly larger than your print bed.
    • S4 Size fits the Alfawise U10 but will hang over the edge slightly of the bed – leave it as it or trim the edge of the mat to fit. Grid size is 400×400.
  • Recommended Temperature Settings
    • PLA: 0C-60C
    • ABS: 90C
      • Our sheets work great with ABS but you MUST use an enclosure for ABS as it warps. If you do not the ABS will stick to the sheet and can pull it off the bed as it warps due to cooling.
    • PETG: 70C
      • PETG has a tendency to like to bond to print surfaces (all brands, not just ours). We recommend using something in-between the mat and the PETG to help it release easier. You can use glue stick or hairspray to prevent this from happening.
      • We use these mats with PETG but we make sure we are not “squishing” it down on the 1st layer as much as you would PLA or other materials. Use a spatula/scraper to remove the prints, DO NOT PULL ON THEM OR TRY TO “KNOCK” THEM OFF.
      • Running a 0.3mm 1st layer height will also ensure that the prints do not adhere too much and damage the mat with PETG.
    • TPU/TPE: 70C
    • PC: 120C
      • Since our mat is based on Polycarbonate we recommend using something in-between the mat and the PC to help it release easier. You can use glue stick or hairspray to prevent this from happening.
  • Returns on sheets are only allowed if they have not been used and/or installed.

Installation Notes/Tips

  1. Clean the surface with acetone then glass cleaner. If you do not have acetone just glass cleaner will suffice.
  2. Align the bed mat on the bed or glass that you want to apply to
    1. Bond strength can also be improved with firm application pressure and moderate heat, from 38°C to 54°C, causing the adhesive to develop intimate contact with the bonding surface.
  3. Peel back one corner
  4. Slowly apply it to the bed pressing firmly as you peel the backing to avoid getting bubbles under the mat

Installation Video

 

Warranty & Support Information

Technical Support: TH3D Community Support

  • To get technical support with this product it is handled through our TH3D Communities
  • Technical support is not included through the TH3D Helpdesk at no charge
    • You are welcome to ask quick questions about a Community Support product through our helpdesk but in-depth 1 on 1 technical support is not included.
  • If you require require a more personalized level of technical support it can be purchased separately in 1 hour blocks of time. Contact Us to get a time-slot paid for and scheduled through one of our technicians.

Warranty Info: 90 Days Warranty

  • Our warranty covers any and all defects with the product.
  • If your product fails or has problems within the warranty period you can contact our support team by emailing Support@TH3DStudio.com or by using the Contact Us link.
    • This is for warranty related issues only, not technical support.
  • Damage/Failure due to improper installation, usage, failure resulting from an issue with the machine the product is installed on, and/or modification or the product is not covered under warranty

 

Best Sellers

Share your thoughts!

4.92 out of 5 stars

35 reviews

Let us know what you think...

One review with a 3-star rating

  1. One person found this helpful

    It's the mat or it's me?

    Dale (verified owner)

    I’m a full-time college student and had been very busy until recently I got out for Christmas break and found the time to put on the mat on my 3D printer and couldn’t be happier for the past 2 days until now none of my filaments are sticking to the bed. I tried cleaning the mat with rubbing alcohol and windows cleaner. Unfortunately, the problem persists.

    (0) (1)

    Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

×

Login

Register

Your personal data will be used to support your experience throughout this website, to manage access to your account, and for other purposes described in our privacy policy.

Continue as a Guest

Don't have an account? Sign Up