3 Pack 100K Thermistor – Hotends and Heated Beds
$8.99
- 1 Meter Wire Length
- Pack of 3 Thermistors
- 2 Wire Connection
- 100K NTC 3950 Thermistor
- Use Marlin #1 Thermistor Setting (Creality Printers and Anet use #1 by default)
- Added option in Unified Firmware for these and all TH3D Thermistors
- Works with all 3D printers that use 100K Thermistors
- See the list below or Contact Us if you want to verify compatibility
In stock
- 1 Meter Wire Length
- Pack of 3 Thermistors
- 2 Wire Connection
- 100K NTC 3950 Thermistor
- Use Marlin #1 Thermistor Setting (Creality Printers and Anet use #1 by default)
- Added option in Unified Firmware for these and all TH3D Thermistors
- MAX temp of 290C.
- Works with all 3D printers that use 100K Thermistors
- Guaranteed to work with
- Anet A2/A6/A8
- Anet E10/E12/E16
- CR-10 (All sizes)
- CR-10S (All sizes)
- CR-X
- CR-10
- CR-10 V2
- CR-10 Pro
- CR-10 Max
- Ender 2/2 Pro/3/3 Pro/4/5/5 Pro/5 Plus/6/7
- Tevo Tornado
- Tevo Tarantula/Tarantula Pro
- And more! Contact Us if you want to verify compatibility
DIY Part Fitment/Installation/Wiring
This is a universal DIY 3D printer part. That means it will work on almost any 3D printer, but you must know what you are doing.
Our technical support does not cover selecting/designing/assisting in firmware setup and/or 3d models to install this part on your printer. If purchased as part of a kit from TH3D for a particular printer, then it will be covered under the kit when using our firmware package.
Electrical replacement parts usually will require you to splice wires into your existing ones for the part you are replacing (soldering and heat shrinking wire splices is recommended for proper connection).
Some of our universal electrical parts come with bare wire ends or plugs on them. These ends may or may not directly plug into your 3D printer. If they do not, you will need to splice the wires into the existing ones on your 3D printer.
Warranty Information
3 Months Warranty - Our warranty covers any and all defects with the product. If your product fails or has problems within the warranty period you can contact our support team by using the Contact Us link. Technical support is limited to the scope of the product itself and not your entire machine.
Damage/Failure due to improper installation, improper usage, failure resulting from an issue with the machine the product is installed on, 3rd party products connected to our product, and/or modification of the product are not covered under warranty.
Share your thoughts!
Let us know what you think...
What others are saying
Related products
Question
Valtteri Pöntiskoski –
so is this same thermistor for ender 5 extruder?
(0) (0) Watch Unwatch
Tor Blazeby –
Yes these work on the Ender5 hotend
(0) (0)
pravotti (verified owner) –
Does this work for the Ender 3 Pro?
The stock thermistor from my machine measures approximately 1.17 M (46″) from glass bulb to plug. If this replacement is 1 M (39.4″) it is too short.
(0) (0)
Tim Hoogland –
This will work. Just cut the stock thermistor cable about 6″ up from the hotend and splice it in. Solder and heatshrink them. You can twist them but in my experience over time the twist gets loose and causes thermistor issues later down the road.
(0) (0)
Question
mverive –
What is the upper temperature rating for this thermistor? I want to print PC with 290-300 degree nozzle temp (using all metal hotend).
(0) (0) Watch Unwatch
Tim Hoogland –
290C is the max temp they are rated for. Higher than that and you will damage them.
(0) (0)
Daniel Linthicum (verified owner) –
It works as advertised! No issues.
(0) (0) Watch Unwatch
Question
Robert Oliver –
will yhese work on the artillery sidewinder x1 bed
(0) (0) Watch Unwatch
Tim Hoogland (verified owner) –
You can use it on any printer bed since this is a universal part. Since the X1 bed has a silicone pad you will want to put the thermistor UNDER the pad between the pad and the bed itself to get the most accurate reading.
(0) (0)
Question
liquid_322 (verified owner) –
Any improvement with this over the stock Ender 6 thermistor?
(0) (0) Watch Unwatch
Tim Hoogland (verified owner) –
This is the same as the stock one.
(0) (0)
Question
Jacob Deets –
Will this work on a CR-10 Mini?
(0) (0) Watch Unwatch
Tim Hoogland (verified owner) –
Yes, this does. These are the same as the stock thermistors.
(0) (0)
Frank Krug (verified owner) –
Wires are short by about 9 inches, but and easy splice and back up and running in no time.
(0) (0) Watch Unwatch
Question
ARegularBear (verified owner) –
Would it be okay to splice on a dupont connector to this and my current thermistor wires so I don’t have to run a new wire through the sleeving to the mainboard?
(0) (0) Watch Unwatch
Tim Hoogland (verified owner) –
We just cut, solder, and heatshrink ours here. Thats what we do!
(1) (0)