Printable Mounts & Wire Management:
Printed Mounts demo (not included print from the above link):
Review from The Edge of Tech
Actual Pictures of the Lighting kit installed on our X1C
$11.99
-
Safe for your printer, unlike kits sold on Amazon, Ebay, and Aliexpress. Upgrade your lighting to see better inside your printer. Plugs into the stock LED port, replacing your stock light. V2 kits include self-sticking cable clips for wire management.
Each LED segment is connected with premium silicone wire and allows for placement on the left, rear, and right inside the printer. Click here for the Installation Guide
62 in stock
Quantity | Discount | Price |
---|---|---|
4-10 | 10% | $10.79 |
11-Unlimited | 15% | $10.19 |
Printable Mounts & Wire Management:
Printed Mounts demo (not included print from the above link):
Review from The Edge of Tech
Actual Pictures of the Lighting kit installed on our X1C
Weight | 4 oz |
---|---|
Dimensions | 3 × 2 × 0.2 in |
Made In | 🇨🇳 China |
Warranty Length | 6 Months |
Nicholas J. Walsh –
What a nice upgrade to the dimly lit PS1. This was a simple install with big results! Thank you TH3D Studio!
Justin Bevins (verified owner) –
I’ve been trying hard not to install any mods to my PS1 but this mod was a no brainer. Easy to install and provides a very nice bright light all throughout the chamber (above the print bed anyhow).
Totally worth picking up especially with how cheap it was. Total install was 10 minutes and half of that was trying to find my IPA!
I did have to turn on my chamber light again as it was off after powering up post install but once I did everything worked as it should.
Herb Halstead (verified owner) –
The difference is incredible. The only issue I had is the video show the X1C install, which shows a different connection setup than is present with the P1S. There is a black tape that shows where the USB port is. Remove that to expose the light plug.
John Gianelli (verified owner) –
I recently purchased a P1S for our local library to enhance their tech programs. It was immediately obvious that with the single light source and tinted door that it was difficult to show the process of 3D printing.
I was very pleased to find this TH3D lighting kit. The quality of the kit is excellent and the online instructions are detailed. Installation was simple and quick with great results.
Victor Oseguera (verified owner) –
I bought this for my P1S and it was super easy to install. Plug and play and running within minutes. Had a question concerning piggyback both lights and was answered immediately. I highly recommended these lights and this company. Buy with confidence in product and support.
Will (verified owner) –
This kit is perfect as you don’t need a riser and it can be controlled directly by the printer, which is hugely convenient. This is ages better than the dinky stock LED. Just note that the inside of the printer is not gonna look perfectly lit like a portrait studio. The placement of the LEDs means there will be some minor shadows depending due to the geometry of the insides, so make sure to stick the LEDs near the edge of the metal overhangs. Overall I’d say this is the most optimized solution for upgrading the LEDs in the printer in terms of cost and convenience!
Inkspiration Station (verified owner) –
I bought this kit for my first P1 S, and when I bought my second one, even my wife said that I needed to Upgrade. It’s very easy to install and seriously improves the visibility in the chamber!
Ariel (verified owner) –
I bought these light kit for my P1S to try them out and the price was great. It was an easy install plug and play. I printed a triangle shaped piece same size of the led to give them an angle pointing the print bed.
Dan Crandell (verified owner) –
Super simple to install, thanks for easy i stall
mjbaldwin0352 (verified owner) –
Once again TH3D ftw. This is an amazing kit. So easy to install and the difference this makes is massive.
I run a sizable farm now and I no longer need to walk over to see how the print is going because I can see it so clearly. Next are the Acrylic doors.
kmcquarters (verified owner) –
A simple and straight forward addition to my printer. A great improvement, thank you Tim.
Jonathan Hagy (verified owner) –
Removed old OEM light from p1s. Printed some clamps to mount on rail. Clamps held & a 45 degree angle there for knocks the glare down looking in at the bed from the top. Also focuses the light towards the be plate. as advertised they do an expellant job. Really lights up the bed. No more looking in around a flashlight sitting on top. The ONLY reason this product was given 4 stars was due to I ordered two of these and one came in with a broken wire @ strip light. Other than that love the way this product brightens every thing up.