Compatible Machines:
- CR-10 and CR-10S – ALL Sizes
- Layer Fan – For use with aftermarket mounts like PETSFang
- Anet A series and E Series
- Layer Fan – For use with aftermarket mounts or stock fan
- Ender 2
- Layer Fan – For use with aftermarket mounts like PETSFang or our EZABL 5015 Mounts
- Alfawise U10
- Layer Fan – For use with aftermarket mounts like PETSFang
- Wanhao i3
- Layer Fan – For use with aftermarket mounts like diiCooler
Installation Notes:
- Be sure to check the polarity on the wires you are connecting our fans to. Typically red is positive and black is negative but some of the Chinese printers do not adhere to these standards.
- There is no list of what machines use what as it can vary from model to model and we have even seen differences in wiring colors used in the same printer models.
- Our fans use red for positive and black for negative. You can verify polarity with a cheap $10 multimeter from Amazon or you local hardware store.
- If fans are shorted out/killed due to improper wiring this is NOT covered under warranty.
Tech Specs:
- 5015 Blower Fan
- Great for Layer Fan Use
- New V2 Fans work without capacitors or the “FAN_FIX” option in firmware
- 12V up to 0.15A power Draw
- DUAL Ball Bearing for 50K+ Hours of runtime
- CFM Rating: 8+ CFM
- RPM: 5200 RPM
- Noise: 37dBA Noise
- 3″ Red/Black Power Lead with 2 Pin JST Plug
- 90 Day Warranty
- Wire Length: 3″
DIY Part Fitment/Installation/Wiring
This is a universal DIY 3D printer part. That means it will work on almost any 3D printer, but you must know what you are doing.
Our technical support does not cover selecting/designing/assisting in firmware setup and/or 3d models to install this part on your printer. If purchased as part of a kit from TH3D for a particular printer, then it will be covered under the kit when using our firmware package.
Electrical replacement parts usually will require you to splice wires into your existing ones for the part you are replacing (soldering and heat shrinking wire splices is recommended for proper connection).
Some of our universal electrical parts come with bare wire ends or plugs on them. These ends may or may not directly plug into your 3D printer. If they do not, you will need to splice the wires into the existing ones on your 3D printer.
Warranty Information
3 Months Warranty -Â Our warranty covers any and all defects with the product. If your product fails or has problems within the warranty period you can contact our support team by using the Contact Us link. Technical support is limited to the scope of the product itself and not your entire machine.
Damage/Failure due to improper installation, improper usage, failure resulting from an issue with the machine the product is installed on, 3rd party products connected to our product, and/or modification of the product are not covered under warranty.
TH3D Employee Timothy Hoogland –
Here at TH3D we use these on all our 12V machines that have 5015 fans (which is most of them). They have been going strong for over a year now with no issues. The cheaper ones from Amazon or eBay lasted about 3-4 months before they failed.
(0) (0) Watch Unwatch
yamichans (verified owner) –
Just a heads up for people buying this to install on 3D printer, the side fan clip on this does not line up with 90% of the duct and you will need to trim it off. Other than that the fan works great.
(0) (0) Watch Unwatch
TH3D Employee Timothy Hoogland –
This does work and doesn’t really affect anything. However the latest EZABL STL Pack has modified mounts that accommodate the fan clip. 🙂
(0) (0)
Antony (verified owner) –
I should have read this. Now deciding whether to dremel my petsfang or the fan.
(0) (0)
Jeff –
Are these brushless?
(0) (0)
Tim Hoogland –
These are brushless.
(0) (0)
Gabriel Bruno (verified owner) –
Had problems with part cooling on my stock CR-10 set-up. Added this fan with a Petsfang system and the improvements have been amazing.
(0) (0) Watch Unwatch