TH3D Uno Bootloader Flashing Kit for 8-Bit Boards Subtotal: $24.99
Dual Z Stepper Motor Adapter w/Cable
$2.99
- Run 2 motors off 1 stepper driver
- Parallel wiring
- Compatible with EZBoard, Creality Boards, MKS Gen L, SKR and many others that use a standard 4 pin JST connection
Only 62 left in stock
- Run 2 motors off 1 stepper driver
- Parallel wiring
- Compatible with EZBoard, Creality Boards, MKS Gen L, SKR and many others that use a standard 4 pin JST connection
Installation
- Simply plug one end of the included cable to your printer Z motor connection.
- Plug the other end into any of the 3 4 pin plugs on the Adapter board
- Plug your 2 motors into the 2 remaining open posts on the adapter board
- Check that the axis moves smoothly. If it does not then increase the VREF by 0.1V until the axis moves smoothly
- Secure the board so that it cannot short out anything. Wrap with electrical tape or print the case below.
- Printable Case for the board: Click here to Download the STL File
Warranty Information
3 Months Warranty -Â Our warranty covers any and all defects with the product. If your product fails or has problems within the warranty period you can contact our support team by using the Contact Us link. Technical support is limited to the scope of the product itself and not your entire machine.
Damage/Failure due to improper installation, improper usage, failure resulting from an issue with the machine the product is installed on, 3rd party products connected to our product, and/or modification of the product are not covered under warranty.
Share your thoughts!
Let us know what you think...
What others are saying
Related products
From: $10.98
From: $10.98
From: $10.98
From: $22.97
From: $19.98
From: $22.97
From: $22.97
Jared Ostergaard (verified owner) –
Works great on my skr 1.3
(0) (0) Watch Unwatch
David –
Does it wire the steppers in series or parallel?
(0) (0)
Tim Hoogland –
Parallel. This is in the product description as well.
(0) (0)
Question
Sy-Ben Jim –
What is the spacing between the two holes? And what size screws do we need to fit it?
(0) (0) Watch Unwatch
Tim Hoogland –
No screws are needed. You can print this tiny bumper case for it that press-fits on to the adapter: https://www.th3dstudio.com/downloads/TH3DDualZAdapterPressOnCase.stl
(0) (0)
Question
daniel.porrey –
Is this needed adapter necessary if I have the split cable that came with the CR10 kit from Creality? This cable has a single connector for the main board and two motor connectors on the opposite end. I am already using this on the stock main board.
(0) (0) Watch Unwatch
Tim Hoogland –
If you have their “Y” cable then it is not needed. You can use the existing cable you have since it is already a splitter.
(1) (0)
Question
erbertchong –
Hi, Dose this adapter spilt the power to the motor in half like some of the online forums mentioned and cause problems? Do I have to recalibrate the z steps or this is a straight forward plug & play?
(0) (0) Watch Unwatch
Tim Hoogland –
This is a parallel wired adapter. No firmware changes are needed on the steps/mm but you should increase your VREF on your Z driver a little bit. Both motors should be identical.
(0) (0)
Question
Jamie Palmer –
Do I need this for the sovol sv01 while running the ezboard 1.2?
(0) (0) Watch Unwatch
Tim Hoogland –
Typically, yes. If you have 2x Z motor plugs on your machine this will allow you to connect the 2 motors to one Z motor header.
(0) (0)