5015 High Speed Sealed Bearing Fan (12V)

Rated 4.50 out of 5 based on 2 customer ratings
(2 customer reviews)

$11.99

  • 5015 Blower Fan
  • Great for Layer Fan Use
  • 12V up to 0.24A power Draw (0.13A typ)
  • Sealed “EverLubricated” Bearing for long life
  • High Airflow vs generic Chinese Fans
  • 3″ Red/Black Power Lead with 2 Pin JST Plug
  • 2 Genuine 3M IDC Connectors for solder-free installation

In stock

Product Details

Compatible Machines:

  • CR-10 and CR-10S – ALL Sizes
    • Layer Fan – For use with aftermarket mounts like PETSFang
  • Anet A series and E Series
    • Layer Fan – For use with aftermarket mounts or stock fan
  • Ender 2
    • Layer Fan – For use with aftermarket mounts like PETSFang or our EZABL 5015 Mounts
  • Alfawise U10
    • Layer Fan – For use with aftermarket mounts like PETSFang
  • Wanhao i3
    • Layer Fan – For use with aftermarket mounts like diiCooler

Installation Notes:

  • Be sure to check the polarity on the wires you are connecting our fans to. Typically red is positive and black is negative but some of the Chinese printers to not adhere to these standards.
    • There is no list of what machines use what as it can vary from model to model and we have even seen differences in wiring colors used in the same printer models.
  • Our fans use red for positive and black for negative. You can verify polarity with a cheap $10 multimeter from Amazon or you local hardware store.
    • If fans are shorted out/killed due to improper wiring this is NOT covered under warranty.

Tech Specs:

  • 5015 Blower Fan
  • Great for Layer Fan Use
  • 12V up to 0.24A power Draw
  • Sealed “EverLubricated” Bearing for long life
  • 7-8CFM Airflow Rating in open air
    • 4-6CFM Installed On Printer (depends on mount/duct)
    • 6000+ RPM
    • ~42dBA Noise
  • 3″ Red/Black Power Lead with 2 Pin JST Plug
  • 90 Day Warranty
  • Wire Length: 3″
  • 2 “UY” quick connectors for solder-free installation
    • See picture below for how to use. Use WIDE pliers and apply equal force.
    • Make sure wires are straight and centered in the connector before squeezing.

Support/Warranty

5015 High Speed Sealed Bearing Fan (12V)

If you are using this at speeds lower than 100% enable the #define FAN_KICKSTART option in our firmware. Otherwise in your slicer there will be an option to “blip” the fan to 100% from idle.

 

Best Sellers

2 reviews for 5015 High Speed Sealed Bearing Fan (12V)

  1. Timothy Hoogland

    Here at TH3D we use these on all our 12V machines that have 5015 fans (which is most of them). They have been going strong for over a year now with no issues. The cheaper ones from Amazon or eBay lasted about 3-4 months before they failed.

  2. yamichans

    Just a heads up for people buying this to install on 3D printer, the side fan clip on this does not line up with 90% of the duct and you will need to trim it off. Other than that the fan works great.

    • Timothy Hoogland

      This does work and doesn’t really affect anything. However the latest EZABL STL Pack has modified mounts that accommodate the fan clip. 🙂

Add a review

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.