Sale!

AnyCubic Chiron LCD Conversion Kit

(1 customer review)

Replace your Chiron LCD with a 12864 for more control and features. Compatible with our EZABL Kits. This kit is designed by TH3D for the AnyCubic Chiron Printers. Pre-setup firmware is included. Comes with ALL the screws, LCD, Housing, PCB Housing, Washers, and Cables needed to install the upgrade. Technical support is included should you need assistance installing the LCD kit.

From: $54.94

26 users have this item in wishlist

TH3D AnyCubic Chiron 12864 LCD Case - ABS

In stock

AnyCubic Chiron LCD Conversion Accessory Parts

Only 16 left in stock

Longer LCD Cables × 2

$1.00 each

In stock

12864 LCD for use with the Chiron

Cables included.

Only 19 left in stock

LCD Mounting/Housing Screws - 8 Pack

This is for 8x LCD Mounting Screw for our Printed Part LCD Housings

In stock

Dupont Jumper Wire Pack - 120 Pieces

Used for connecting from the PCB to the control board

30CM

Unified 2 Firmware for the AnyCubic Chiron

3 Months
AnyCubic Ramps Printers

Have an ABL probe?

Replace your Chiron springs with our solid bed mounts

Add on the bootloader flashing kit?

Later models of the Chiron may not have a bootloader. This kit allows you to flash it.

In stock

Description

What is this kit for and why should I get it?

This kit replaces the stock touch LCD to give you more control and features over YOUR printer.

The stock LCD does not give you access to tuning settings like acceleration, jerk, steps per mm, and many others. This also allows for live Z adjustment (babystepping) and much more control over the core operations of your printer. PID tuning is available as well to fine-tune your hotend and bed temperature regulation. This goes great with our EZABL kit for automatic bed leveling.

Requires a firmware update that is included with the purchase of this kit. The Chiron usually has a bootloader already (but some later models do not) and updates the firmware over it’s USB port. See the firmware page for full details on how to use and update the firmware.

BOOTLOADER DISCLAIMER: SOME later Chiron models may not have a bootloader. You can check if yours has one by trying to update the firmware before purchasing to see if it will upload to the board. If the firmware uploads to the board, then you have a bootloader installed. If the firmware upload fails with a timeout error then you need to install the bootloader. If your board does take our firmware and you want to use the printer without the LCD kit you will need to re-flash the stock firmware that you can get from the AnyCubic site here: https://www.anycubic.com/pages/firmware-software

Will this work with Klipper?

Yes, these LCDs and the stock board are supported by Klipper firmware. However, due to the complexity of Klipper, our technical support that is included does NOT apply if you are using Klipper firmware. Technical support only applies when you are using our Unified 2 Firmware package that is included.

SD Card Slot – You will use the SD slot on the left side of the LCD after this kit is installed. The stock SD slot is not used and is removed during the installation.

Magnet Nozzle Switch – If your Chiron came with the magnetic nozzle “leveling” switch, this is not supported with our firmware and we do not have plans to add support for it in the future. If you wish to have fully automatic bed leveling we highly recommend pairing this LCD kit with our EZABL kit.


Installation Directions & Video

Click here for the installation directions & video guide

Click here for the Chiron Bootloader Installation Guide

Additional information

TH3D AnyCubic Chiron 12864 LCD Case - ABS

Weight 5 oz
Dimensions 5 × 5 × 3 in
Made In

🇺🇸 USA (with 🇺🇸 USA and 🌎 Global Materials)

Warranty Length

6 Months

AnyCubic Chiron LCD Conversion Accessory Parts

Weight 3 oz
Dimensions 2 × 2 × 2 in
Made In

🇺🇸 USA (with 🇺🇸 USA and 🌎 Global Materials)

Warranty Length

6 Months

Longer LCD Cables

Weight 2 oz
Dimensions 1 × 1 × 1 in
Made In

🇨🇳 China

Warranty Length

6 Months

12864 LCD for use with the Chiron

Weight 6 oz
Dimensions 4 × 4 × 1 in
Made In

🇨🇳 China w/QC in 🇺🇸 USA

Warranty Length

6 Months

LCD Mounting/Housing Screws - 8 Pack

Weight 1 oz
Dimensions 0.5 × 0.5 × 0.5 in
Made In

🇨🇳 China

Warranty Length

SOLD AS-IS, NO WARRANTY

Dupont Jumper Wire Pack - 120 Pieces

Weight 5 oz
Dimensions 5 × 3 × 2 in
Length

30CM

Made In

🇨🇳 China

Warranty Length

6 Months

Unified 2 Firmware for the AnyCubic Chiron

Update Length

3 Months

Firmware Package

AnyCubic Ramps Printers

Made In

🇺🇸 USA

Have an ABL probe?

Weight 4 oz
Dimensions 2 × 2 × 2 in
Made In

🇺🇸 USA (with 🇺🇸 USA and 🌎 Global Materials)

Warranty Length

6 Months

Add on the bootloader flashing kit?

Weight 4 oz
Dimensions 6 × 6 × 2 in
Made In

🇨🇳 China w/QC in 🇺🇸 USA

Warranty Length

6 Months

1 review for AnyCubic Chiron LCD Conversion Kit

  1. Larry F. (verified owner)

    Works perfectly

Add a review
SHARE YOUR CART