Tough All-Metal Hotend w/ Nozzle Pack (Steel+Brass) – V6 Compatible – 12V/24V
From: $27.99
- Fully Compatible with all V6 hotend Mounts
- Based on E3D V6 Open Source Design under GPL V3
- ALL METAL Heatbreak
- 0.4mm Brass, 0.6mm Brass, 0.4mm Steel, and 0.6mm Steel Nozzles Included
- 1 Meter PTFE Tubing
- 2x PTFE Fittings (one for hotend and one for extruder)
- 2x 100K NTC 3950 Thermistors
- Use Marlin #1 Thermistor Setting (Creality Printers and Anet use #1 by default)
- Added option in Unified Firmware for these and all TH3D Thermistors
- 40W 12V Heater Cartridge
- 40W 24V Heater Cartridge
- 30mm 12V Fan with Blue Shroud
- 30mm 24V Fan with Blue Shroud
- Full details below
Upgrade your printer to print exotic and high temp materials (up to 290C). Real all-metal assembly, even in the heatbreak, unlike other cheap hotends on the market.
Tips for Using This Hotend
- All Metal Heatbreak Information: Using your All Metal Hotend
- We recommend if you are getting jamming with PLA (this can happen with ALL METAL heatbreaks from any manufacturer) to print a filament oiler.
- Like this one: https://www.thingiverse.com/thing:492067. Stuff it with a sponge or fiber then lightly wet with CANOLA oil. This will oil the filament path and keep the PLA from sticking to the heatbreak on a longer retract.
- After using this for about a month or two your heatbreak should have a nice “seasoning” on the inside and use of an oiler will be needed less or not at all.
- Read the Using your All Metal Hotend article for more information
Technical Specs
- Fully Compatible with all V6 hotend Mounts
- Based on E3D V6 Open Source Design under GPL V3
- ALL METAL Heatbreak
- 0.4mm Brass, 0.6mm Brass, 0.4mm Steel, and 0.6mm Steel Nozzles Included
- Compatible with 1.75mm Diameter Filament
- 1 Meter PTFE Tubing
- 2x PTFE Fittings (one for hotend and one for extruder)
- 2x 100K NTC 3950 Thermistors
- Use Marlin #1 Thermistor Setting (Creality Printers and Anet use #1 by default)
- Added option in Unified Firmware for these and all TH3D Thermistors
- 40W 12V Heater Cartridge
- 40W 24V Heater Cartridge
- 30mm 12V Fan with Blue Shroud
- 30mm 24V Fan with Blue Shroud
- Basic Documentation Included with Assembly/Disassembly Guide
- Heater, Fan, and Thermistor Pre-Tested
- Installation assistance through our ticket system included
- If you print over 260C you may need to insulate the heater block from the cooling fan to reach high temperatures.
- We sell Silicone Socks separately and you can add them on above.
Mounts for Various Printer Models
Below are links to mounts that work with this hotend for popular models. If your model is not listed go to Thingiverse and search “your printer model V6 Mount”. We also do printing so if you need a mount printed please submit a print request to us for a quote.
- Creality 3D Printers
- CR-10/CR-10S/Ender 3/Ender 3 Pro Models
- Hero Me (for use with standard heaterblock): https://www.thingiverse.com/thing:3291101
- Hero Me (for use with High Flow/Volcano heaterblock): https://www.thingiverse.com/thing:3370065
- PETSFang: https://www.thingiverse.com/thing:2759439
- Heavy Duty V6: https://www.th3dstudio.com/product/cr-10-cr-10s-e3d-v6-heavy-duty-mount-5015-fan-and-ezabl/
- Click here to search Thingiverse for more mounts for this model.
- Ender 5/Ender 5 Pro/Ender 5 Plus Models
- Simplify E3DV6: https://www.thingiverse.com/thing:3682669
- Hero Me (for use with standard heaterblock): https://www.thingiverse.com/thing:3291101
- Hero Me (for use with High Flow/Volcano heaterblock): https://www.thingiverse.com/thing:3370065
- Click here to search Thingiverse for more mounts for this model.
- CR-10/CR-10S/Ender 3/Ender 3 Pro Models
- Anet Printers
- Anet A8
- Mount 1: https://www.thingiverse.com/thing:2099577
- Carriage V4: https://www.thingiverse.com/thing:2193695
- Click here to search Thingiverse for more mounts for this model.
- Anet A8
DISCLAIMER: All these mounts are community designs. TH3D Studio LLC is not responsible for any issues with these 3rd party links. They are provided for convenience to you so you do not have to search for mounts. This hotend is compatible with almost every E3D V6 or “V6” type mount for any printer model.
Assembly Video
Hotend will ship un-assembled as seen below
Part Fitment/Installation
This is a universal 3D printer part. That means it will work on almost any 3D printer (check your printer voltage and part voltage) with the correct mount for your specific machine. Thingiverse is a wonderful place to locate mounts and we also have printed parts in our shop for some universal parts.
It is up to you to determine and select a mount for your specific printer model (or design one) to install this part on your machine and wire it up to your machine (if applicable). You are welcome to Contact Us for recommendations for your particular printer model for mounting options that are available online if searching yourself does not yield any results.
Warranty & Support Information
TH3D Community Support - Technical support for the product is handled through our TH3D Communities. You can get access to them on our Community Page.
3 Months Warranty - Our warranty covers any and all defects with the product. If your product fails or has problems within the warranty period you can contact our support team by using the Contact Us link. This is for warranty related issues only, not technical support.
Damage/Failure due to improper installation, improper usage, failure resulting from an issue with the machine the product is installed on, 3rd party products connected to our product, and/or modification of the product are not covered under warranty.
This is NOT an E3D product. This is based on their open source design. Compatible with all “V6” style mounts.
Share your thoughts!
Let us know what you think...
What others are saying
Related products
$11.04
From: $10.49
$11.04
$59.49
$40.49
$11.04
$1.69 – $2.54
$6.99
$5.59
$11.04
$58.49
From: $40.49
$12.50
jwilliams (verified owner) –
After having issues with my stock hotend and wanting to reliably be able to print other material then PLA, I went with the TH3D V6 with the titanium heatbreak. Installation was quick and painless and I’ve had zero problems with it.
After reading the number of people who said all metal hotends had trouble with PLA I was afraid I’d experience clogs but taking the advice of using an oiler, I’m happy to say I haven’t had a single issue.
As long as you take the time to make sure it’s properly installed and your PID is correctly tuned, this is a great upgrade to have.
(1) (0) Watch Unwatch
Question
athattarath (verified owner) –
Can you use the stock Creality Ender 5 carriage/mount with this hotend? Also, thank you for answering my other question.
(0) (0) Watch Unwatch
Tim Hoogland –
You can use the stock carriage but will need a hotend mount to attach to the carriage. Mounts like the HeroMe can do this: https://www.thingiverse.com/thing:4460970
If you cannot print the parts due to a mechanical issue or other issues we do not sell the HeroMe parts pre-printed we do accept print requests through our Contact page if you select “Print Farm” as the department and provide the STL files you want to be printed.
(0) (0)
Question
athattarath (verified owner) –
Would my Ender 5 firmware be compatible with the new hotend and heater block provided in the kit?
(0) (0) Watch Unwatch
Tim Hoogland –
Yes, it uses the same thermistor and 40W heater that the Creality hotends use.
(0) (0)
Question
mark Platt –
Can this be used as a direct replacement on the sovol sv-01 without the Bowden setup?
(0) (0) Watch Unwatch
Tim Hoogland –
Yes, this will fit the SV01 in place of the stock hotend. They use a V6 style hotend like this one.
(0) (0)
Question
Mike Guderjohn (verified owner) –
I just bought this, and printing the parts for my Ender 3, with the EZ Board (I bought it a couple weeks ago.) So I’ve gone to the Unified Firmware link to make a firmware for that board.
In the description here it says to “Use Marlin #1 Thermistor Setting (Creality Printers and Anet use #1 by default)” then follows it with this: “Added option in Unified Firmware for these and all TH3D Thermistors” The software config has an option for the TH3d thermistors, but also has the Creality thermistor as the first choice.
So I HAVE to ask, which do I use? This is kind of confusing, since the product page says 2 conflicting things.
I selected the TH3D thermistor, but I sat on that decision for a good 10 minutes until I finally made a choice. Hopefully I don’t burn anything up.
(0) (0) Watch Unwatch
Mike Guderjohn (verified owner) –
Thanks Tim. I’m building the Hero Me ducting as we speak, and then hopefully testing everything out sometime later today. Need to take a break with all the fiddly stuff, right now. Old age, bad eyes and arthritis in the hands not helping matters one bit… 🙂
(0) (0)
Tim Hoogland –
It uses #1 if using Marlin (not our version) or the TH3D Thermistor option (which also sets #1 in the backend).
(0) (0)
TreeClocker67 (verified owner) –
Definitely not a required upgrade for my Ender 3, but well worth it, especially if you want to convert to direct drive and eliminate long bowden tubes.
Test the resistance of the heater core before installing everything. I didn’t check before installing and my printer was faulting for thermal runaway. One of the crimped wires that connected to the heater cartridge wasn’t making contact. Slid the insulation back, re-crimped the connectors, fixed the insulation, added a some Kaplon tape and she was up and runnin.
Zero issues printing PLA, PETG, etc. I haven’t had to oil the hotend after swapping filament types, yet.
At the price point I recommend the upgrade.
(1) (0) Watch Unwatch
Jpenna1983 (verified owner) –
I have had no problems with this hotend. I have mine mounted with the e3d v6 pets fang mount and a 5015 blower fan. I’ve been printing tons of prints and I have had no clog at all. I printed the oiler but I haven’t used it yet. All calibrations test pass and PID auto tune holds temp very well. I am very happy with this Hotend.
(1) (0) Watch Unwatch
recreant359 (verified owner) –
Well machined, easy to assemble with a plethora of assembly guides and instructions on the web. Heats up even faster than stock, and with the heavy duty mount is still light enough that it doesnt affect travel at all! I recommend also getting the silicone sock set.
(0) (0) Watch Unwatch
Alex Eckman (verified owner) –
Much better than stock! Higher temps and tons of aftermarket mount options available
(0) (0) Watch Unwatch
Thomas Butler (verified owner) –
Arrived, a day earlier than expected. Well packaged and well labelled, no guessing which part was what voltage. Installation video was concise and to the point. Total install less than an hour including soldering the heater and thermistor, and printing perfect on first print…. My printer is quickly becoming a TH3E E16…..
(0) (0) Watch Unwatch
CRUISER DON RUSSELL (verified owner) –
SEINCE I’VE BEEN DOING SO MUCH TO MY ENDER 3, I HAD TO REDO THE HOT END TOO ! HAVEN’T PUT IT TO WORK YET, BUT SOON ! NICE
(0) (0) Watch Unwatch
deleonc (verified owner) –
great product, easy installation with all the packaging being labeled with 12v or 24v. go for the upgrade options will be worth every bit!
(0) (0) Watch Unwatch
Gabriel Bruno (verified owner) –
I got this all metal hotend because I was printing at higher temps. Little did I know that this thing is a beast for all my materials! Very easy installation and the TH3D team has excellent videos and articles on this product.
(0) (0) Watch Unwatch
Israel repetti (verified owner) –
Straight magic! Makes printing with wood pla much easier.
(0) (0) Watch Unwatch
sakura.j.lim (verified owner) –
This took a bit of time for me to install properly but now that I have it done I am so happy. Just remember to set our retraction to no more than 3 mm, though 2mm is prefered. I would recommend pairing this with the high temp tough tubing, titanium heat break, and heavy duty mount. Bear in mind the mount would also require a 5015 layer fan and should also use the CR10s old fan as its 40mm instead of the 30mm thats included on this system.
Amazing support from the community and TH3D which helped me fix all my problems !
11 out of 10, will purchase from again!
(0) (0) Watch Unwatch
Question
athattarath (verified owner) –
Does this use a 5015 fan?
(0) (0) Watch Unwatch
Tim Hoogland –
You can use one if the mount you choose has a 5015 layer fan option. The Heavy Duty V6 and the HeroMe use a 5015. We also carry 5015 fans in 12V and 24V here.
(0) (0)