TH3D EZBoard V2+ – For Creality/Sovol Printers – Unified 2, Marlin, & Klipper

CR-10 (Regular, Mini, S4 S5)

CR-10S (Regular, Mini, S4 S5) – Usually needs Creality Dual Cable LCD Adapter (addon above)

If your CR-10S LCD has an EXP3 plug on it then you do NOT need the Dual Cable LCD adapter.

Does NOT work with Touch Screen Models

CR-10 V2 and CR-10 V3 are not supported due to mounting differences with the stock board

CR-20 – Needs CR-20 specific Dual Cable LCD Adapter (addon above)

Ender 2

Ender 2 Pro – Requires cable adapter kit

Ender 3/3 Pro

Ender 3 V2 – Needs LCD swapped.

See here for details: Ender 3 V2 – Swapping to the 12864 Creality LCD for more features – TH3D Studio LLC

Ender 3 MAX

Both layer fans will need to be spliced to use one connector as our board has one header for the layer fan.

Ender 5/5 Pro

Ender 5 Plus – Needs other addons/upgrades listed below

Needs the 12864 LCD Conversion Kit and the Creality Dual Cable LCD adapter (addon above)

Does NOT work with the stock Touch Screen, only with the 12864 LCD Conversion linked above

Ender 6

Needs the 12864 LCD Conversion Kit

Does NOT work with the stock Touch Screen, only with the 12864 LCD Conversion linked above. NOTE the SD slot is on this board so the stock extension will not work. You can use a SD Extension to extend it and replace the stock SD extension. This SD extension works with the Ender 6 SD Extension Adapter Plate that we made.

Sovol SV01

Sovol SV01 Pro

Requires 12864 LCD Conversion Kit

Does NOT work with the stock Touch Screen, only with the 12864 LCD Conversion linked above

Sovol SV03

Sovol SV06 – Requires extra wiring for the stock ABL sensor.

You can re-wire and modify the stock ABL 5 pin plug or use jumper wires to make the connection. See here for details and pictures: https://support.th3dstudio.com/helpcenter/ezboard-v2-sovol-sv06-stock-abl-sensor-wiring/

Note that this is only required for the stock ABL sensor. If you are also converting to our EZABL kit then you will not need to use the stock ABL sensor plug.

V2+ Edition – Includes EZBoard V2, MiniUSB Cable, and 4GB MicroSD Card

CPU – STM32F405RGT6 – 168mhz, 32-Bit, 1MB Flash, 192K RAM

Official Firmware – TH3D Unified 2 (Based on Marlin 2)

3rd Party Firmware Support** – Marlin 2.X+, Klipper

Voltage Compatibility – 12-24V DC Input

PCB – 4 Layers, 2oz Copper every layer

Stepper Drivers – 4x Trinamic TMC2209 in UART Mode – 2A RMS, 2.8A Peak Output, Sensorless homing capable

Hotend Output – Up to 8A Max Load*

Heated Bed Output – Up to 13A Max Load*

2x Fan Outputs – Up to 2A Max Load*

Filament Sensor Port – Works with our EZOut sensor and OEM Creality/Sovol sensors

NeoPixel Port – Onboard port for powering up to 2A of 5V NeoPixels directly from the board

BL Touch Port – BL Touch (SERVO) header Onboard

5V Rail Isolation – Prevents backfeeding USB power to the PSU input terminal

Other Details & Features

• Onboard 4K EEPROM Chip
• Onboard Dual Z Motor Output headers (parallel)
• Hotend Thermistor VIN short protection
• Bed Thermistor VIN short protection
• Flyback Diodes on all MOSFETS
• Serial Header Onboard

*The EZBoard V2 comes with a 15A main fuse. Exceeding 15A total draw will blow the fuse. Up to 20A fuse can be used for higher load machines.

**Please note that our included technical support is limited to our Unified 2 Firmware as Klipper and Marlin are for advanced setups for advanced users. We do have technical support available at an additional charge for advanced setups or applications that fall outside of the standard product support scope.